How To Cut Old Window Glass

• How To'southward & Quick Tips

How To: Cut Drinking glass

Get a perfect pane for your project with this step-past-pace guide.

Photo: dreamstime.com

If the very idea of cutting drinking glass makes you cringe, perhaps it'south because you retrieve a painful occasion when glass cut you. Yet while circumspection is required, cutting a slice of glass—to, say, supersede a broken window, frame a film, or top a tabular array—is literally a snap to DIY. And it tin certainly relieve cash: Hiring a handyman or professional window installer to replace a pane tin can cost upwards of $100.

The essential tool at play in your project is a glass cutter, though its name is somewhat misleading. This inexpensive, pencil-sized implement with a carbide- or diamond-tipped cycle in its head scores, rather than slices through, the surface. Once that'southward done, you just snap the pane along the directly line. A beginner with any fears about the process should vesture goggles (in the unlikely upshot of flying shards) and work gloves for protection (keeping in mind that thicker gloves could impair dexterity). It's likewise smart to practise on scrap drinking glass till you get the hang of it, but before long yous'll be custom-plumbing fixtures panes similar a pro!

The process for cutting glass follows these simple steps:

1.  Thoroughly make clean the drinking glass you lot intent to cut.
2.  Lay the glass on a clean, flat, layered surface.
3.  Measure the glass to the required dimensions.
4. Score the glass with a drinking glass cutter, using a straightedge for guidance.
5. Snap the glass along the scored line.
6. Shine out whatever precipitous edges.

Tools & Materials

• Drinking glass cutter
• Work gloves
• Safety goggles
• Solvent
• Cutting oil
• Framing square
• See full list «
• Ruler
• Record measure
• Mark pencil
• Square-jaw pliers
• Dowels
• Sandpaper
• Sharpening stone

Photo: dreamstime.com

Step i

Outset, get your glass squeaky clean. Dirt or grime volition interfere with the cutter's operation, resulting in an uneven border. Using glass cleaner or solvent, thoroughly wipe down both sides of the pane. Make sure the wheel of the cutter is clean as well, by dabbing a chip of lubricating cut oil on the tip with a rag.

Stride ii

For best results, set up a clean, flat, layered surface on which to cut the glass. A plywood or a similarly resilient work table is all-time, cushioned with a few sheets of butcher paper, newspaper, or fabric, smoothed to eliminate bumps.

Footstep 3

Identify the glass on your prepped surface and use a framing square, ruler, or tape measure to mensurate it to the required dimensions.

When cutting windows of identical size—such every bit double-paned windows—yous tin utilize a cut pane instead of the framing square to measure the second window.

To measure a replacement pane for a window frame, remove about ¼ inch from the length and width of the frame'south opening and then the glass fits well once glazing is added to its edges. Mark the score line with a marker pencil if you want a visual guide, but information technology's non necessary to marking more than starting and stopping points for elementary, straight cuts; a straightedge works as a scoring guide.

Footstep 4

Score! If you plan on wearing goggles and gloves, gear up now. To score the glass, place the straightedge along the line or marks yous fabricated. If the straightedge feels slippery, put a piece of masking record on the underside to improve its stability. Dab a drop of cut oil on the cutter wheel, and place the side of the tool against the straightedge at the far end of the cut line. Pull the tool toward yous, using moderate force in one polish glide. If you hear a ripping audio, you've got the pressure just right; if it sounds like in that location'southward dust on the glass, easy up. Continue going in ane single motion until y'all achieve the stop. Retracing the score mark increases the likelihood of ragged edges and a bad break.

Step v

Remove the straightedge and lift the glass. Lay a long dowel directly under the score line and place ane palm on either side of the mark. Press firmly to snap the glass in two.

Step half dozen

The edge of the drinking glass will be sharp! Trim remainder slivers or chips with square-jaw pliers if your glass cutter's head doesn't have nibbling slots. If using pliers, put cloth or cardboard scraps between the glass and the plier jaws to pad the glass. Use fine-grit sandpaper or a sharpening stone to dull the edge and make the pane safer to handle.

Your next move is perfectly clear: Time to place the glass y'all've cut and cross one more household repair from your to-do listing.

Source: https://www.bobvila.com/articles/how-to-cut-glass/

Posted by: mcgeethiped.blogspot.com

Share this post